If your GE dishwasher is not functioning properly, it could be due to a faulty control board. The control board is the brains of the appliance, and it is responsible for controlling all of the dishwasher’s functions. In this article, we will discuss how to tell if your GE dishwasher control board is bad and what you can do to fix the problem.
Understanding the role of the dishwasher control board
The dishwasher control board plays a critical role in the functioning of your dishwasher. It acts as the brain of the appliance, controlling and coordinating all the different components to ensure that the dishwasher runs smoothly. The control board receives input from various sensors and switches, and uses that information to determine the appropriate actions that need to be taken. It is responsible for regulating the water temperature, timing the wash cycles, and monitoring the status of the dishwasher’s various components. If the dishwasher control board is malfunctioning, it can cause a range of issues, including failure to start, failure to complete cycles, or even electrical problems. However, diagnosing a faulty control board can be difficult, and it is often necessary to consult with a professional to accurately identify and fix the problem. Overall, understanding the role of the dishwasher control board is essential for ensuring the proper functioning of your dishwasher and avoiding costly repairs in the future.
Common symptoms of a faulty dishwasher control board
A faulty dishwasher control board can cause a range of problems that can be frustrating for any homeowner. One of the most common symptoms of a faulty dishwasher control board is when the machine fails to start altogether. Another symptom is when it starts and then stops mid-cycle. The timer on the dishwasher may also not be functioning properly, causing dishes to come out either still dirty or still wet. In some cases, the dishwasher may even start itself without any human input. These symptoms can be caused by a variety of issues with the control board, including faulty wiring or damaged circuits. If you notice any of these symptoms, it’s important to address the issue as soon as possible to avoid further damage to your dishwasher and to ensure it operates efficiently.
| SYMPTOM | POSSIBLE CAUSES | POTENTIAL SOLUTIONS |
|---|---|---|
| Dishwasher not starting | Faulty control board, wiring issue, defective sensor | Replace control board or sensor, repair any wiring issues |
| Buttons not responding | Faulty control board, broken buttons, wiring issue | Replace control board or broken buttons, repair any wiring issues |
| Error codes appearing on display | Faulty control board, sensor issue, wiring issue | Replace control board or sensor, repair any wiring issues |
| Dishwasher not filling with water | Water inlet valve issue, wiring issue, control board issue | Replace water inlet valve, repair any wiring issues, replace control board if necessary |
| Dishwasher not draining | Drain hose clog, faulty drain pump, wiring issue, control board issue | Unclog drain hose, replace drain pump, repair any wiring issues, replace control board if necessary |
| Dishwasher not cleaning dishes | Faulty wash motor, spray arm issue, water inlet valve issue | Replace wash motor or spray arm, clean or replace water inlet valve if necessary |
| Dishwasher making unusual noises | Faulty wash motor, defective pump, worn bearings | Replace wash motor or pump, repair or replace worn bearings |
| Dishwasher leaking water | Faulty door gasket, loose or damaged connections, damaged tub | Replace door gasket, tighten or repair damaged connections, replace damaged tub |
| Dishwasher stopping mid-cycle | Control board issue, wiring issue, sensor issue | Replace control board or sensor, repair any wiring issues |
| Dishwasher overfilling | Faulty water inlet valve, control board issue, wiring issue | Replace water inlet valve, replace control board if necessary, repair any wiring issues |
| Dishwasher not drying dishes | Faulty heating element, control board issue, wiring issue | Replace heating element, replace control board if necessary, repair any wiring issues |
| Dishwasher display not working | Faulty display board, wiring issue, control board issue | Replace display board, repair any wiring issues, replace control board if necessary |
| Dishwasher door not latching | Door latch issue, wiring issue | Replace door latch if necessary, repair any wiring issues |
| Dishwasher running for too long | Control board issue, sensor issue, wiring issue | Replace control board or sensor, repair any wiring issues |
| Dishwasher not dispensing detergent | Dispenser issue, control board issue, wiring issue | Replace dispenser, replace control board if necessary, repair any wiring issues |
How to perform a diagnostic test on your GE dishwasher control board
Your GE dishwasher control board may be the brains of your dishwasher, but when it’s not functioning properly, it can be difficult to determine exactly what’s causing the problem. Luckily, performing a diagnostic test on your control board can help you quickly identify any issues and take the necessary steps to fix them. Here’s how to perform a diagnostic test on your GE dishwasher control board:
- Start by turning off the power to your dishwasher at the circuit breaker. This will ensure your safety while you work on your appliance.
- Next, locate the diagnostic test mode instructions in your dishwasher’s user manual. These instructions will guide you through the steps necessary to enter the diagnostic test mode.
- Once you’ve entered diagnostic test mode, you can begin testing your control board. Follow the instructions provided in the user manual to run through each test and record any error codes that appear.
- Once you’ve completed all of the tests, review your results to determine the cause of the problem. If you’re unsure of what the error codes mean, refer to your user manual or contact a professional for assistance.
Performing a diagnostic test on your GE dishwasher control board can help you quickly identify any issues and take the necessary steps to fix them. By following these steps and consulting your user manual, you’ll be well on your way to getting your dishwasher back up and running in no time.
Replacing vs repairing a bad GE dishwasher control board
The decision to replace or repair a bad GE dishwasher control board can be a difficult one. On one hand, repairing the board may seem like a cost-effective solution, but it can also be unpredictable. There’s no telling whether the repaired board will hold up over time or if other problems will arise. On the other hand, replacing the board can be a substantial expense, but it offers peace of mind knowing that you’re starting fresh with a brand new, reliable part. The burstiness of the situation lies in the fact that there are often unforeseeable complications that can arise during either process, adding to the perplexity and making it difficult to predict which option is the best for your specific situation. Ultimately, it’s important to weigh the pros and cons and consider factors such as the age of your dishwasher, the cost of the repair or replacement, and your overall budget before making a decision.
Tools and equipment needed to test and repair a GE dishwasher control board
Repairing a GE dishwasher control board can be a daunting task, but having the right tools and equipment can make the process easier. To begin with, you will need a set of screwdrivers, both flathead and Phillips, to open the dishwasher and access the control board. A multimeter is also essential to test the board’s electrical connections. A soldering iron and soldering wire will come in handy if you need to repair any damaged connections. Additionally, you may need a heat gun to remove any stubborn components from the board. Finally, a replacement control board may be necessary if the current one is beyond repair. By having these tools and equipment on hand, you will have everything you need to test and repair a GE dishwasher control board.
| TOOL/EQUIPMENT | PURPOSE | COST | AVAILABILITY | ADDITIONAL NOTES |
|---|---|---|---|---|
| Multimeter | To measure voltage and test continuity | $50-$100 | Commonly found at hardware stores | Recommended for any electrical testing |
| Soldering iron | To re-solder connections | $20-$50 | Commonly found at hardware stores | Recommended for experienced users only |
| Desoldering braid | To remove old solder | $5-$10 | Commonly found at hardware stores | Be sure to use proper safety precautions when using |
| Soldering flux | To help with soldering | $5-$10 | Commonly found at hardware stores | Recommended for experienced users only |
| Heat gun | To remove old solder and components | $20-$50 | Commonly found at hardware stores | Be sure to use proper safety precautions when using |
| Screwdrivers | To remove and install components | $10-$20 | Commonly found at hardware stores | Be sure to use the proper size and type for the task |
| Pliers | To manipulate small components and wires | $10-$20 | Commonly found at hardware stores | Be sure to use the proper type for the task |
| Wire strippers | To strip insulation from wires | $10-$20 | Commonly found at hardware stores | Be sure to use the proper size and type for the task |
| Isopropyl alcohol | To clean circuit board and components | $5-$10 | Commonly found at hardware stores | Be sure to use pure isopropyl alcohol and follow safety precautions |
| Cotton swabs | To apply isopropyl alcohol | $5-$10 | Commonly found at hardware stores | Be sure to use lint-free swabs and avoid touching components |
| Anti-static wrist strap | To prevent static damage to components | $10-$20 | Commonly found online | Recommended for any electronics repair |
| Magnifying glass | To inspect small components and solder joints | $5-$20 | Commonly found at hardware stores | Recommended for detailed inspection |
| Light source | To illuminate work area | $10-$20 | Commonly found at hardware stores | Recommended for detailed work |
| Epoxy | To secure components and wires | $5-$10 | Commonly found at hardware stores | Be sure to use the proper type and follow safety precautions |
| Hot glue gun | To secure components and wires | $10-$20 | Commonly found at hardware stores | Be sure to use the proper type and follow safety precautions |
Step-by-step guide to testing a GE dishwasher control board for faults
The GE dishwasher control board is a crucial component of your dishwasher that helps to regulate its functions. If you suspect that your dishwasher control board may be faulty, you will need to test it to confirm. To assist you, we have put together a step-by-step guide to help you test your GE dishwasher control board for faults.
Step 1: Disconnect the Dishwasher
Before you begin testing your GE dishwasher control board, you will need to disconnect the dishwasher from its power source. This step is essential to ensure your safety while working with electrical components.
Step 2: Access the Control Board
The next step is to locate the control board. The control board is usually located at the top of the dishwasher, behind the control panel. To access the control board, you will need to remove the screws that hold the control panel in place.
Step 3: Inspect the Control Board
Once you have access to the control board, you will need to inspect it for any signs of damage or wear. Look for any burnt spots, swollen capacitors, or loose connections on the board. If you notice any of these signs, it is an indication that the control board is faulty.
Step 4: Test the Control Board
To test the control board, you will need a multimeter. Set the multimeter to the Ohms function and touch the probes to the appropriate terminals on the control board. Refer to your GE dishwasher control board manual for the correct terminal locations. If the reading on the multimeter is not within the range specified in the manual, it is an indication that the control board is faulty.
Step 5: Replace the Control Board
If the control board is faulty, you will need to replace it. You can purchase a new control board from your local appliance store or online. Before you install the new control board, make sure to carefully read the installation instructions provided with the new board. Once installed, reconnect the dishwasher to its power source and test the dishwasher to ensure that it is functioning correctly.
Following these steps will help you to identify and test a faulty GE dishwasher control board. If you are unsure or uncomfortable with any of the steps, it is always recommended to seek the assistance of a professional technician.
Tips for troubleshooting a GE dishwasher control board
If you suspect that your GE dishwasher control board is bad, there are a few things you can do to troubleshoot the issue. First, check the power supply to ensure that the dishwasher is getting the correct voltage. You can also inspect the wiring and connections to the control board for any damage or loose connections. Another common issue with control boards is that they can become clogged with debris, so it’s important to clean the control board regularly to prevent this from happening. If you’ve tried these tips and still can’t determine if the control board is bad, it may be time to call in a professional for assistance.
| PROBLEM | POSSIBLE SOLUTIONS |
|---|---|
| Dishwasher won't turn on | 1. Check power supply 2. Check door switch 3. Check control board |
| Dishwasher isn't cleaning dishes properly | 1. Check spray arms 2. Check water inlet valve 3. Check filter 4. Check control board |
| Dishwasher is leaking | 1. Check door seal 2. Check tub gasket 3. Check water inlet valve 4. Check drain hose 5. Check control board |
| Dishwasher is making strange noises | 1. Check spray arms 2. Check wash impeller 3. Check drain impeller 4. Check motor bearings 5. Check control board |
| Dishwasher is not draining | 1. Check drain pump 2. Check drain hose 3. Check garbage disposal 4. Check control board |
| Dishwasher is not filling with water | 1. Check water inlet valve 2. Check float switch 3. Check control board |
| Dishwasher is not drying dishes | 1. Check rinse aid dispenser 2. Check heating element 3. Check control board |
| Dishwasher is not completing cycle | 1. Check control board 2. Check door latch 3. Check timer 4. Check thermostat |
| Dishwasher is not dispensing detergent | 1. Check dispenser actuator 2. Check dispenser solenoid 3. Check control board |
| Dishwasher door won't latch | 1. Check door latch assembly 2. Check strike plate 3. Check control board |
| Dishwasher is overfilling | 1. Check water inlet valve 2. Check float switch 3. Check control board |
| Dishwasher is underfilling | 1. Check water inlet valve 2. Check float switch 3. Check control board |
| Dishwasher is not cleaning dishes on upper rack | 1. Check spray arm 2. Check water tube 3. Check water inlet valve 4. Check control board |
| Dishwasher is not cleaning dishes on lower rack | 1. Check spray arm 2. Check wash impeller 3. Check water inlet valve 4. Check control board |
| Dishwasher is not cleaning dishes at all | 1. Check spray arms 2. Check wash impeller 3. Check water inlet valve 4. Check filter 5. Check control board |
How to safely remove and install a new GE dishwasher control board
Replacing a GE dishwasher control board might seem like a daunting task, but with the right steps, it can be done safely and effectively.
Before you begin, make sure you have the necessary tools and replacement part. Here’s how you can safely remove and install a new GE dishwasher control board:
- Turn off the power supply to your GE dishwasher by unplugging it from the wall or turning off the circuit breaker.
- Open the dishwasher door and remove the screws that hold the control panel in place. Carefully disconnect any wires that are attached to the control board.
- Take a photo or make a note of the wire connections so you can easily reconnect them later.
- Unscrew the old control board from the dishwasher and carefully remove it.
- Install the new GE dishwasher control board and attach it to the dishwasher with screws.
- Reconnect the wires to the new control board, making sure they are in the correct positions.
- Replace the control panel and attach it with the screws you removed earlier.
- Turn the power supply back on and test the dishwasher to ensure the new control board is working properly.
By following these steps, you can safely remove and install a new GE dishwasher control board without damaging your dishwasher or risking injury.
Where to find replacement GE dishwasher control boards
Finding replacement GE dishwasher control boards can be a tricky task. There are a few different routes you can take, but none of them are guaranteed to work. One option is to check with your local appliance repair shops. They might have a spare control board lying around that they can sell to you. Another option is to scour online marketplaces like eBay and Amazon. However, be careful when buying from third-party sellers, as they may not be legitimate or may be selling counterfeit items. Your best bet might be to contact GE directly and inquire about purchasing a replacement control board. However, this can be a time-consuming process and may require you to provide specific information about your dishwasher model. In any case, it’s important to do your research and compare prices between sellers to ensure you’re getting a fair deal on a genuine replacement control board.
| STORE | PRICE | WARRANTY | SHIPPING |
|---|---|---|---|
| Appliance Parts Pros | $235.99 | 1 year | Free |
| Repair Clinic | $195.00 | 365 days | Free |
| Easy Appliance Parts | $226.87 | 1 year | Free |
| GE Appliance Parts | $232.50 | 1 year | Free |
| Parts Dr | $220.00 | 1 year | $6.95 |
| Mara Industrial | $207.75 | 1 year | Free |
| Jetson Appliance Parts & Services | $195.00 | Free | |
| Ebay | $155.00 | Free | |
| Amazon | $235.99 | Free | |
| Sears Parts Direct | $222.96 | Free | |
| Global Solutions Appliance Repair | $235.00 | Free | |
| Part Simple | $232.50 | Free | |
| Midwest Appliance Parts | $221.16 | Free | |
| Dishwasher Repair Parts | $220.00 | Free | |
| A-1 Appliance Parts | $243.40 | Free |
Preventing future problems with your GE dishwasher control board
Having issues with your GE dishwasher control board can be frustrating and may cause significant damage to your dishwasher. Preventing future problems can save you time and money. One way to prevent future issues is to make sure the dishwasher’s electrical connections are secure and free of corrosion. You can also ensure that the dishwasher is installed correctly and level to avoid any unnecessary strain on the control board. Additionally, you can prevent future problems by regularly cleaning your dishwasher and avoiding overloading it. Finally, be sure to follow the manufacturer’s instructions and use only recommended detergents and rinse aids. By taking these preventative measures, you can help extend the life of your GE dishwasher control board and avoid costly repairs.
There are several signs that may indicate a bad control board. The dishwasher may not turn on, the display may not work properly, or the dishwasher may not complete its cycle. Additionally, if the dishwasher is making strange noises or leaking water, it could be a sign that the control board is malfunctioning. If you suspect that your control board is bad, it’s best to consult with a professional for diagnosis and repair.
In some cases, a bad control board may be able to be repaired rather than replaced. However, this depends on the specific issue with the board and the expertise of the technician performing the repair. It’s best to consult with a professional to determine the best course of action for your dishwasher.
There are several factors that can contribute to a control board malfunctioning. These can include power surges, moisture damage, and general wear and tear over time. Additionally, if the dishwasher is not maintained properly or is subjected to excessive use, this can also cause issues with the control board.
No, attempting to repair a control board yourself can be dangerous and may cause further damage. It’s best to consult with a professional for diagnosis and repair. Additionally, tampering with the control board may void any warranty that you have on the appliance.
The cost of replacing a GE dishwasher control board can vary depending on the specific model of your dishwasher and the cost of labor in your area. In general, you can expect to pay between $150 and $300 for the replacement part and installation. However, it’s best to consult with a professional for an accurate estimate based on your specific needs. How can I tell if my GE dishwasher control board is bad?
Can a bad control board be repaired?
What causes a control board to go bad?
Is it safe to attempt to repair a control board myself?
How much does it cost to replace a GE dishwasher control board?
In conclusion, identifying a faulty control board in your GE dishwasher is crucial in ensuring that your appliance continues to function well. The symptoms of a bad control board include unresponsive touchpad, failure to start, and erratic behavior. However, before replacing the control board, take the time to troubleshoot other possible causes of the problem like the power source and wiring. If you are not confident in your ability to identify and fix the problem, it is always wise to enlist the services of a professional technician to avoid further damage to your appliance.
Comments
40 responses to “How to Determine if Your GE Dishwasher Control Board is Faulty”
What are the signs that a GE dishwasher control board is faulty?
There are several signs that may indicate a faulty control board in a GE dishwasher, such as not starting or stopping mid-cycle, not responding to commands, or displaying an error code. It is recommended to troubleshoot the problem and replace the control board if necessary.
Comment question text
Comment answer text
What are the common symptoms of a faulty GE dishwasher control board?
Some common symptoms of a faulty GE dishwasher control board include the dishwasher not starting, not completing a cycle, or not responding to buttons on the control panel. Additionally, you may notice unusual sounds or error codes displayed on the panel. It’s important to diagnose and fix a faulty control board to ensure your dishwasher is working properly.
Comment question text here
Comment answer text here
What are the common signs of a faulty control board in a GE dishwasher?
Some common signs of a faulty control board in a GE dishwasher include the dishwasher not starting, the lights not working, or the dishwasher not responding to commands. It’s important to troubleshoot and diagnose the issue to determine if the control board is indeed faulty before replacing it.
What are the common signs of a faulty dishwasher control board?
Some common signs of a faulty dishwasher control board include the dishwasher not turning on or starting, the dishwasher not completing a cycle, the dishwasher not responding to button inputs, or the dishwasher displaying error codes. If you are experiencing any of these issues, it may be worth checking the control board for any visual signs of damage or malfunction.
Random Comment Question?
Random Comment Answer.
Can a faulty control board cause my GE dishwasher to stop working completely?
Yes, a malfunctioning control board can cause your GE dishwasher to stop working entirely or may lead to issues like not starting, not responding to commands, or stopping mid-cycle.
What are the common signs of a faulty GE dishwasher control board?
Some common signs of a faulty GE dishwasher control board include the dishwasher not starting, not responding to touch, or not completing cycles. You may also notice that the lights on the control panel are not working or that the dishwasher is making unusual sounds.
What are some common signs of a faulty GE dishwasher control board?
Some common signs of a faulty GE dishwasher control board include the dishwasher not starting, buttons not responding, and error codes appearing on the display. It is important to diagnose and fix the issue as soon as possible to prevent further damage to the appliance.
What are the most common signs of a faulty GE dishwasher control board?
Some of the most common signs of a faulty control board in a GE dishwasher are the machine not starting, not completing a cycle, or displaying error codes. Additionally, you may also notice that the lights on the control panel are not working or that the dishwasher is making unusual sounds.
What are the common symptoms of a faulty GE dishwasher control board?
Some common symptoms of a faulty GE dishwasher control board include the dishwasher not starting, buttons on the control panel not responding, and lights on the control panel not turning on. Additionally, the dishwasher may fail to complete a cycle or may display error codes.
What are the common signs of a faulty GE dishwasher control board?
The common signs of a faulty GE dishwasher control board include the dishwasher not starting, buttons not responding, lights not turning on, and the dishwasher not completing cycles. If you notice any of these signs, it’s best to verify the issue with a qualified technician and replace the control board if required.
What are some common symptoms of a faulty GE dishwasher control board?
Some common symptoms of a faulty GE dishwasher control board may include the dishwasher not starting, the control panel not responding, or the dishwasher cycling on and off unpredictably.
What are the common signs of a faulty GE dishwasher control board?
Some common signs of a faulty GE dishwasher control board include unresponsive buttons, erratic behavior of the dishwasher, failure to start or complete a cycle, and error codes displayed on the control panel.
How can I test if my GE dishwasher control board is faulty?
To determine if your GE dishwasher control board is faulty, you can start by checking for any error codes displayed on the control panel. These error codes can provide valuable information about the specific issue. Additionally, you can try resetting the control board by unplugging the dishwasher for a few minutes and then plugging it back in. If the problem persists, you may need to consult a professional technician or consider replacing the control board.
How can I test if my GE dishwasher control board is faulty?
To determine if your GE dishwasher control board is faulty, you can start by checking for common signs. If the dishwasher doesn’t respond to any button presses, shows error codes, or fails to start or complete a cycle, it could indicate a control board issue. Additionally, if you notice any burning smells or visible signs of damage on the control board, it’s likely faulty. However, it’s always recommended to consult a professional technician for an accurate diagnosis and proper repair.
Is it possible to fix a faulty GE dishwasher control board on my own?
While it is technically possible to fix a faulty GE dishwasher control board on your own, it is highly recommended to seek professional assistance. Dealing with electrical components can be dangerous if you do not have the proper knowledge and experience. It is best to contact a qualified technician who can diagnose the issue accurately and safely repair or replace the control board if necessary.
Can I fix a faulty control board on my GE dishwasher myself?
While it is possible to fix a faulty control board on your GE dishwasher yourself, it is not recommended unless you have experience and knowledge in appliance repairs. Handling electrical components can be dangerous, and without proper expertise, you may end up causing more damage. It is best to consult a professional technician who specializes in dishwasher repairs to ensure the issue is diagnosed correctly and fixed safely.
Is it possible to fix a faulty control board on a GE dishwasher?
Yes, it is possible to fix a faulty control board on a GE dishwasher. However, I would recommend consulting a professional technician who specializes in appliance repairs to properly diagnose and fix the issue.